I have a vsxtreme 2000 I loaded the new file today and it has been auto rolling for the passed hour on bev did a factory reset , installed new factory file and the the newest file and waited again still auto rolling switched over to dish works fine checked the cable that's not it check the signal thats at 72 % with 69 % quality tried to download guide it won't work not sure what to do next .

thanks in advance

__________________
SEARCH BUTTON it really works

Tired of waiting days for fixes? Click here to get 3000 channels.. NO DOWNTIME, Guaranteed!

did you try and turn the autoroll off.

__________________
IN GOD WE TRUST. keep that always
testing pansat 9000hd and sv4000

http://www.maritime-fta.com/

did that no video no audio did not work any other ideas

try a hard boot leave off for a minute or 2 as we all know bevs been doing alot of fun stuff the last little while if all else fails try to enter newest keys manually and see if that works ive done that a few times in the past and it seemed to work so its worth a try

__________________
testing sv 4000 cw 800 captain 7100 SV360Elite sv 360 premier Viewsat/Plat-lite viewsat lite
Try these channel if having difficulty with EPG.
Sat.... Cha
61.5.....574,195
82........2718
91. ......218
110......321
119......239,200

ok did hard reboot left off for 5 mins checked keys 4 times and still nothing anything else I could try , it's so strange that dish pulls in right away and bev nothing but trouble this time around .

thanks again

here is another strange thing if I go into antenna setup and change the setup to bev 82 and do a channels scan I get doulbe channels of what I got and they work but when I hooked up old bev reciever and check signal it shows bev 91 not 82 so I know I am pointed onto the right sat

just because you set it to 82 doesnt mean thats what it is same as any of the others before you do your scan make sure top right it says the signal your trying to set up otherwise it will scan in double channels of another sat you have a signal for if it was me id do a factory reset start fresh set one sat at a time scan scannels in repeat until you have all sats scanned

__________________
testing sv 4000 cw 800 captain 7100 SV360Elite sv 360 premier Viewsat/Plat-lite viewsat lite
Try these channel if having difficulty with EPG.
Sat.... Cha
61.5.....574,195
82........2718
91. ......218
110......321
119......239,200

I have done a factory reset like 20 times I have 1 cable 1 dish hooked to one reciever pointed at bev 91 I have another dish pionted at dish 110 and a nother pionted at 119 I am not using any switch or anything eles 1 straigh cable to the riecver scaning only one sat at a time so I'm not getting sats mixed up what I was saying is that I do the setup for bev 91 everything fine there then I do an auto scan nothing wrong there when that is done I go to a channel and leave it there for 15 mins and then try a nother channel all it does is autoroll now with out hooking up another dish or doing anything else I go back into setup slect sat bev 82 and then do an auto scan and it downloads more channels now keep in mind I did not move the dish or cable all I did was change sat settings now I have some doulbe channels and they work change channel the one downloaded for bev 91 nothing just autoroll ,

thanks again

__________________
SEARCH BUTTON it really works

Have two working Xtreme's so have a bit of knowledge with Xtreme's. Since the Bev is the problem let's work thru Bev only and you can add in the others after Bev.

As brat6990 mentioned we have to make sure your dish is locked onto Nimiq1

Try this:

1. Factory Default
2. Connect only the Bev dish to the Xtreme
3. Go into Installation then Antenna setup
4. Select Nimiq1 for the satellite (make sure of these settings) Lnb 11250 , tp 12224, DisEQc none
5. At this point if you are locked onto Bev (on the top of the screen) directly across from "Antenna Setup" you should see the words Nimiq 1. This indicates you are locked onto Nimiq1. If you are not locked onto Bev@91 degrees you will not see Nimiq1.
6. If this is correct I would then exit which puts you into the screen where you can scan so I would just scan that one satellite. (Not Blind Scan)
7. Exit, Exit an so on all the way out. Hopefully you will have Bev now.
8. If auto-rolling I would first go to a non-scrambled channel to verify there is a picture. If yes then go to 220 (A-London) and let it roll

My thought is that you are choosing Nimiq 1 (91 degree) and the scan is scanning for those transponders/frequencies on that satfile. Then when you do another blind scan you are scanning everything so if you are not locked onto Bev you are scanning all transponders and frequencies from whatever you are pointed at with that dish.

My belief is that your dish might be on Nimiq 2 vice Nimiq 1. Wish I was there to help.

__________________
Testing: Viewsat Xtreme, Sonicview 360Elite
Suggest this hard drive: SimpleTech SimpleDrive SP-UF35/500 GB USB 2.0 External Hard Drive (designed by Pininfarina)

Visit the Site Sponsor for your FTA needs:
http://www.maritime-fta.com/

so far everything you have said I have done the only thing I notice is that it does not say nimic 1 directly across from "Antenna Setup" but I am pointed at nimic 91 used old bev reciever to set it up , another thing I noticed is that in antenna setup it says nimic 1, 30,0 (W ) once I select that it shows in the antenna setup box nimic 1, 30,0 ( E ) not ( W )

Tired of waiting days for fixes? Click here to get 3000 channels.. NO DOWNTIME, Guaranteed!