CW600P Out-Of-Box Setup


HOW TO FLASH.
You can flash (load) your receiver with a bin on top of the bin (file) you already have. It will replace it.
Use a Null CABLE RS232 on your receiver from the computer. Or use a Null adaptor from Radio Shack number 26-264B to make a straight through cable a Null cable. Take the cable off going to the LNB to be safe. If you don't have a 9 pin plug on your computer you may need to use a USB to Serial cable 26-183 at Radio Shack with a Null adaptor. If you need a 9 pin mail to mail gender adapter it is item #: 26-231. You will need to install a drive in your computer for the USB cable.

Un-zip all the files and hook up the cable from your computer to the STB, have the STB off with the switch in the back. Start the loader and click on the FILE folder. Find the bin file you un-zipped that now ends in BIN. Click on it and it will automatically go in the loader. Select DOWNLOAD S/W then select a COM PORT. You can flash several ways. NOT on the remote but in front of the receiver hold in the power button as you turn the switch ON in the back. The word BOOT will stay on the STB front panel. Now you can click START on your loader and the % should move up. Or you can flash in the standby mode if you use a USB cable. Standby mode is when you have the receiver ON in the back and OFF with the remote. You will see the time or --:-- if there is no time. Don't do anything as the progress bar is going across. Make sure the Computer & STB are done before you go to the next step. They may not get done at the same time. The receiver needs up to one minute to process the data after the computer is done, (DON'T RUSH THIS). The receiver will count down twice then show "-End". When done turn receiver OFF & ON from the back. You may need to do a FACTORY DEFAULT instructions below. If your box is a virgin you will need to download the factory file for it, load that then load the latest third party realese.

PLUGGING IN CABLE.
Make sure you plug in the cable from the d*sh to the receiver at the LNB IN. The cables coming from the d*sh to the switch should be put on the switch at the same number as you have set in your receiver. "Example", 119 cable goes on number 1 on the diseqc switch and the receiver has #1 for 119 in the program. You can only get one Satellite for each one LNB you have. Two LNB's two Satellites, and so on.

82W/91W/110W/119W all have a LNB Freq of 11250

you will see quality on trans 12224 or 12253 or 12268 (depending on the satellite or your location)

THIS IS WHAT THE SETTINGS ARE. You can start here then change them later.
MENU, SYSTEM SETTING, SYSTEM
Menu Language------------English
Audio1-----------------------English
Audio2-----------------------English
Close Caption---------------OFF
Channel NO.-----------------SID (Selecting SID means your channels will be in proper order, just as if you were a sub)
TV System-------------------NTSC
TV Screen Format----------AUTO
Recall History----------------OFF
Auto TP-----------------------ON
Key Update Message--------ON
bev&dn Full Name-----ON

MENU, SYSTEM SETTING, OSD, OK
Background--------------------B-1 or User (if uploaded)
OSD Transparency-------------7
Display Icon-------------------YES
Auto Exit Channel List--------YES
EPG Style----------------------New
Hor Offset---------------------+00
Ver Offset---------------------+00
Time Out----------------------5 Sec
Channel List-----------------CH-10
Time Display Format---------12
Auto Roll----------------------ON

AUTO ROLL KEYS QUICKER:
When a key change happens and the receiver has been off to not receive it, sometimes certain channels wont roll fast (better the quality the faster it will roll),
I find the best way for bev Is to roll on 211 or 281.
and for dn channel 200 or 239

SCAN A SATELLITE FOR CHANNELS
When done the above and still in your Satellite Settings click the red AUTO button on the remote to scan that Satellite. Do it to each Satellite you want. Say NO to only FTA channels wanted. The PROGRESS bar will move down and the screen will change when done each Satellite.

SCAN A TP
MENU, INSTALLATION, MANUAL SEARCH, side arrow & pick a satellite. Then down to FREQUENCY, then change to what you want, then down to SEARCH TYPE change to ALL then OK.

SELECT ECHOSTAR & b*ll PACKAGES
Press the “SAT” Button from your remote and choose the option.

TURN TP AUTO-ROLL OFF & ON
MENU, SYSTEM SETTINGS, SYSTEM then down arrow to AUTO TP then side arrow to change.
HOW TO TURN OFF KEY AUTO-ROLL
MENU, SYSTEM SETTING, OSD, AUTO-ROLL on or off

BLIND SCAN
Main Menu, Installation, Antenna Setting. Then selecting a satellite, press YELLOW key on your remote.

IMPORTAIN, PATCH ENABLE - SET DEFAULT KEY
On remote click the F1 key then the number key 0 three times. If you get a message PATCH DISABLE then do it again to get PATCH ENABLE that will set the default key.

DO A FACTORY DEFAULT
MENU, INSTALLATION, FACTORY DEFAULT, ALL, NO, YES, OK.
When you do this in ALL you will also clean out your channels and Satellite settings.

ENTER KEYS MANUALLY
MENU, ACCESSORIES, KEY MENU, OK
Then side arrow to NAGRA2, then down arrow to 00 01 01 d*sh NET, then click on the GREEN button at the bottom of the remote that says PAUSE. Don't change the ProviderID or the index number. Move arrow over to KEY.
When you get the keys you need to know what line number to put the keys on your receiver. So this may help you to put the keys on the correct line.
Keys 00 or 86 go on line 80
Keys 01 or 96 go on line 90
You can pick a letter with the down arrow & use the number pad for numbers. When done you need to click the OK under all the letters with the OK on the remote to keep in what you changed.

OR

Goto a channel and press page down, it will give you a key menu, you can edit the key by pressing the green button.

ICON FILE
This step is NOT necessarily needed. It will show an icon when you first go to a channel something like when you see ABC, NBC & CBS on the TV screen. You can flash this bin several ways. One way is to do it the same way you did the bin file, in the S/W on the loader and BOOT on the STB. After flashing the Icon bin you must turn the feature ON. Main Menu, System settings, OSD, Display Icon, Yes.

SET GMT TIME
MENU, CHANNEL MANAGER, TIMER. TIMER SETUP, side arrow to AUTO, down to TIME ZONE.

CHANGE TIME FROM MILITARY TO REGULAR 12/24
MENU, SYSTEM SETTING, OSD, TIME DISPLAY FORMAT 12 or 24



cp

__________________

Tired of waiting days for fixes? Click here to get 3000 channels.. NO DOWNTIME, Guaranteed!